Anchor NAVI-TRAC 40 WIDE HIP-END User Manual

Please read all assembly / installation instructions before the installation or removal of this product.1100 Burch Dr., Evansville, IN 47725 Ph. 812

10SQUARE UNIT TOP FRAME COMPLETESUMMARY OF STEPS FOR COMPLETING THE SQUARE TENT1. INSTALL OPPOSITE EAVES, RAFTERS, HIPS AND HIP BRACES TO COMPLET

11LIFTING TOP FRAME (FIRST SIDE)INSTALL UPRIGHTS. AT INTER-MEDIATE LOCATIONS, INSTALL UPRIGHT BRACES AS WELLUPRIGHT BRACESUSING HEAVY-DUTY NAVI-TRAC

12* IMPORTANT NOTE: REFER TO CAUTION STATEMENT #2 FOR IMPORTANT WARNING ABOUT NUMBER OF STAKES SUPPLIED. (SEE BACK PAGE OF THIS MANUAL)THE INSTALLER

13TENSIONING AND GUYING1. USE WEB/RATCHETS TO SECURE CATENARY ARCHES TO UPRIGHTS, STAKE BASEPLATES BEFORE TENSIONING WEBS.2. ATTACH GUY WEBS TO EAVE

14HIP END MODULES FOR RECTANGULAR UNITSTHE RECTANGULAR UNIT IS SIM-PLY (2) HIP ENDS FACING EACH OTHER AND SEPARATED BY PAR-ALLEL-BEAMED MIDDLE BAYS.NO

INSTALLING MID BAY PURLINS AND EAVE/RIDGE BARSCONNECTION SEQUENCE MAY CHANGE WITH THE TERRAINNOTE: FABRIC ONLY INDICATED, SO THAT FRAME WILL BE MORE

16INSTALLING MID PANELINSERT FINGERS OF WHEELED PANEL GUIDE INTO THE OPEN END OF THE RAFTER AND WELDMENT. TIGHTEN THE BUTTERFLY NUT. REVERSE FOR OPP

UNITS WITH (2) OR MORE MID BAYSADDITIONAL GUIDE BARS CAN BE PURCHASED123MIDDLE BEAMS THAT ARE NOT A PART OF AN END MODULE USE THE HINGED BASEPLATE (FO

1840’ NAVI-TRAC COMPLETEWITH (2) 15’ MID BAYS1. ALL ENGINEERING ON THE 40’ NAVI-TRAC WAS DONE WITH THE WALLS IN PLACE. (FULLY ENCLOSED

19Wall InstallationStep 1Determine which side of wall is inside and out. Ground bar pockets are on outside, Lace fl ap is on inside. Start by feeding

2 Table of Contents Page No. Assembly Step 3 Introduction Inspect Site Frame Terminology 4 Component Illustrations

20Groundbar keeper for inter-mediate upright.Groundbar keeper for Cor-ners.Prong with no hole inserts up into upright.Cross sectional view of upright.

Anchor products are of superior design and operate best within the parameters of these instructions. It is imperative that the instructions be care

INTRODUCTION:The NAVI-TRAC frame configuration is based on the hip roofed square tent shown below. Hip bars connect corners to the peak, and rafters

40’ NAVI-TRAC COMPONENT ILLUSTRATIONSINSTALLATION TOOLS4

5HARDWARE LOCATION CHART40’ NAVI-TRAC COMPONENT LISTOTHER COMPONENT NOTES:1. FOR X-CABLES FOR UNITS 100’ OR LONGER, SEE PAGE 17 FOR LABELING, QUANTIT

640’ NAVI-TRAC Installation Safety GuidelinesYour installation techniques will evolve to fit the needs of your clients, the experience level of your c

7DIRECTIONS FOR SQUARING THE TENT1. USE A TAPE MEASURE TO MARK THE ENDS OF A LINE FOR ONE END (A TO B ABOVE) EQUAL TO THE EXACT WIDTH OF THE UNI

LAYOUT END MODULE COMPONENTSCONSTRUCT FIRST BEAMNOTE: ON END MODULES, EAVE FIT-TINGS FOR BOTH EAVES AND RAF-TERS ARE RIGID SLIP JOINTS.HOOK THE END

91342657INSTALL DROP-IN HIPS AND HIP BRACES IN THE ORDER SHOWN. HINT: TO ALIGN HIP BRACES , LIFT CENTER OF HIP BAR, THEN DROP THE HIP BRACE CONNEC-T